Select Your Region


    •  
Products

KOA Corporation > Product > How to Use > Current Fuses and Fusing Resistors

Current Fuses and Fusing Resistors

How To Use Current Fuses and Fusing Resistors

Current Fuses and Fusing Resistors

Current Fuses are one of the simplest devices to protect a circuit. The resistors with fusing function protect the equipment or parts from burning by breaking the abnormal current in a malfunction such as short-circuiting. TF, CCP , and CCF are lined up.
This product also has the fusing function. It works to fuse and prevent semiconductor element or resistor from burning or firing when the current exceeding fusing power is dissipated.
Fusing resistors are suitable where certain resistance is required for using a circuit and a failure of any other device might cause smoke or fire. In general, blow speed is slower than that of current fuse, it will not be recommended for instantaneous fusing requirement. Check fusing resistor lineup of leaded resistors for RF73 RF RF26 RF25CC and WF.


Current Fuses Fusing Resistors
Normal function Zero current path Specified value resistor
Overload Blow Blow
Cause of blow Over current Over power dissipation
Fusing Characteristics Instantaneous fusing
Precise fusing
Slow blow
Wide scatter in fusing

Application Examples of Current Fuses

One piece of the fusing product is enough as long as the fuse of the main power supply is fused when any local failure of power circuit is caused. But the power supply of today's equipment is divided into several independent blocks and the main power supply unit sometimes fails to detect the malfunction in terminal where current is small. A failure, severe enough to cause a danger in the local block, might not always be detected at the main fuse.
To design a safe circuit, we recommend fuses or some protective devices should be included in each branch or block so circuits shall not emit smoke or catch fire even if a malfunction like short-circuit or motor lock is caused in each block.

Diagram of TF

Current Fuses, where to use
Diagram of TF structure

電流ヒューズの使用例 構造図

Diagram of CCP structure

電流ヒューズの使用例 構造図

Diagram of CCF structure

電流ヒューズの使用例 構造図


Application Example of Fusing Resistors

In the IC circuit recommended, a resistor is inserted in to the power supply Vcc in series, it works as a current limiter, and at the same time as a decoupling device with noise together with the capacitor.
But in case of failure, when the IC or the capacitor is short circuited, depending on the supply voltage and resistance value, the resistor may emit smoke or catch fire without operating any protector circuit. Fusing Resistors RF RF73 are suited to break the current without burning.

ヒューズ抵抗の使用例

Resistors to suppress parasitic oscillation of emitter follower circuit

Emitter follower circuits are often used to realize low output impedance amplifiers. But they can oscillate parasitically unless proper attention is paid. When this phenomenon is overlooked, unexpected trouble may be caused, e.g. EMI. Moreover, it is difficult to check oscillation because the condition is so delicate as to be changed by touching with a probe of an oscilloscope. Still more, oscillation can be stopped even with changing temperatures.
An effective solution for this kind of oscillation will be to decouple the collector from the Vcc and to put a resistor Rb, ranging from several 10 to several 100, to the base circuit as illustrated. When the emitter load is capacitive, inserting a low resistance resistor into the load in series also has an effect.
For power amplifiers, this series resistance becomes very small. And it might bring about unexpected heating or going up in smoke depending on the transistor failure mode. In such situations, Fusing Resistors RF or RF73 which has a fuse function is recommended. Rush current should be taken into consideration together when choosing Fusing Resistors.

Resistors to suppress parasitic oscillation of emitter follower circuit

Resistors to stabilize FET switching operation

MOSFET is popular high frequency switching device. A gate resistor of a low value has an effect of stabilizing switching operation. If resistance is too low, it may give instability due to chattering at transistor "on" and "off" transient. On the other hand, the waveform becomes dull if gate resistance is too high. Therefore the suitable value should be determined by observing the waveform. This consideration is especially important for power MOS devices, because the gate resistance may have correlation to surge voltage and switching energy loss.
For power MOSFET, this gate resistance becomes very small. And it brings unexpected heat and emission of smoke due to the transistor failure mode. In such situations, Fusing Resistors RF or RF73 which has a fuse function is recommended. Rush current should be taken into account together when choosing Fusing Resistors.

Resistors to stabilize FET switching operation
Resistors to stabilize FET switching operation 2

Inventory